KitchenAid induction cooktop
showing FC E0
FC E0 brings the induction module into the picture.
Mon–Sat, 8am–8pm
- Induction power and coils
- Induction board and coil repair
- Source: KitchenAid
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What FC E0
actually means.
FC E0 brings the induction module into the picture. KitchenAid lists the electrical supply, the associated wiring and the induction module itself, the board that drives the coils under the glass.
KitchenAid cooktop display
What to do when FC E0 shows on the cooktopKind of codeInduction power and coils
An induction zone could not drive its coil as the board planned: no pan was detected, the current ran too high or too low, or the power stage reported trouble. The pan base, the supply voltage and a clogged air intake are checked before the coil or the power board is replaced, and a top that trips its breaker is left switched off until then.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Element Not Heating
A coil stays black, a radiant ring under the glass never glows, or a zone warms so weakly that a pot of water will not boil.
MakeKitchenAid
A Whirlpool brand with cooktops aimed at people who cook often.
SourceKitchenAid Product Help: FC E0, electric and induction cooktop
KitchenAid electric and induction cooktops.
Before you book,
in this order.
Each step comes from KitchenAid's own guidance for FC E0 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Switch the breaker off for one minute, then back on.
Watch the cooktop for a minute.
If FC E0 returns, book a visit for the induction module and supply.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
FC E0 is not a pan-detection prompt. It concerns the power side of the induction system.
What you may
notice with it.
The cooktop problems FC E0 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Where FC E0 usually leads
Induction board and coil repair.
KitchenAid
cooktops.
A Whirlpool brand with cooktops aimed at people who cook often.
KitchenAid cooktop repair
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In KitchenAid's own words
There may be a problem with the electrical supply, the associated wiring, or the Induction Module.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. KitchenAid electric and induction cooktops.
KitchenAid FC E0 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about FC E0.
Can I clear FC E0 myself?
What is the induction module on a KitchenAid cooktop?
Can FC E0 come from my home's wiring?
Why does the induction module matter for FC E0 on a KitchenAid cooktop?
Back to your everyday
Still showing FC E0?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.