Gaggenau cooktop
showing E9000
E9000 and E9010 tell you the voltage reaching the Gaggenau cooktop is too high or too low.
Mon–Sat, 8am–8pm
- Induction power and coils
- Induction board and coil repair
- Source: Gaggenau
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E9000
actually means.
E9000 and E9010 tell you the voltage reaching the Gaggenau cooktop is too high or too low.
Gaggenau cooktop display · also shown as E9010
What to do when E9000 shows on the cooktopKind of codeInduction power and coils
An induction zone could not drive its coil as the board planned: no pan was detected, the current ran too high or too low, or the power stage reported trouble. The pan base, the supply voltage and a clogged air intake are checked before the coil or the power board is replaced, and a top that trips its breaker is left switched off until then.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Tripping Breaker
The circuit breaker for the cooktop trips as a burner or zone switches on, at one particular setting, or a few minutes into cooking.
MakeGaggenau
A German luxury maker, part of the BSH group, known for built-in cooking sold into custom kitchens.
SourceGaggenau CI 292 602 induction cooktop use and care manual (en-us), Troubleshooting
From the troubleshooting table of Gaggenau's US manual for the CI 292 602 200 series induction cooktop; the codes are printed in a display typeface and were read from the rendered page.
Before you book,
in this order.
Each step comes from Gaggenau's own guidance for E9000 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Switch the breaker off.
Do not reset the breaker again and again while waiting for the check.
Have the utility or an electrician check the supply before booking a visit.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
These codes are not about cookware or a single zone. They report the supply voltage at the cooktop.
What you may
notice with it.
The cooktop problems E9000 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Tripping Breaker
6 causes, cheapest first
Where E9000 usually leads
Induction board and coil repair.
Gaggenau
cooktops.
A German luxury maker, part of the BSH group, known for built-in cooking sold into custom kitchens.
Gaggenau cooktop repairMore Gaggenau codes
All 14 Gaggenau codesInduction power and coils on other makes
In Gaggenau's own words
The supply voltage is incorrect. It is outside the normal operating range.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. From the troubleshooting table of Gaggenau's US manual for the CI 292 602 200 series induction cooktop; the codes are printed in a display typeface and were read from the rendered page.
Gaggenau E9000 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E9000.
Can I clear E9000 myself?
Who do I contact first about E9000?
Does E9010 mean something else?
What should the utility check when a Gaggenau shows E9000?
Back to your everyday
Still showing E9000?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.