Wolf CT induction cooktop
showing E44
Each Wolf induction zone has a sensor that watches its temperature.
Mon–Sat, 8am–8pm
- Temperature and overheat sensors
- Induction board and coil repair
- Source: Wolf
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E44
actually means.
Each Wolf induction zone has a sensor that watches its temperature. E44 says one of those sensors reads open, and Wolf notes that the affected burner is shut down.
Wolf cooktop display
What to do when E44 shows on the cooktopKind of codeTemperature and overheat sensors
A sensor under the glass or on a board reported a reading the control rejected, or heat climbing past the safe limit — often after an empty pan was left on a zone. The zone is allowed to cool and a loose sensor plug is ruled out before the sensor, the coil assembly or the board is blamed. A top that keeps getting hotter is switched off at the breaker first.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Element Not Heating
A coil stays black, a radiant ring under the glass never glows, or a zone warms so weakly that a pot of water will not boil.
MakeWolf
The cooking half of Sub-Zero Group, selling cooktops and rangetops from its Wisconsin base.
SourceWolf answer: CT induction cooktop, error code E44
Wolf CT series induction cooktops.
Before you book,
in this order.
Each step comes from Wolf's own guidance for E44 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Reset the cooktop at the breaker.
Turn the power back on, switch on a burner and see whether E44 comes back.
If it does, book a visit.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
E44 is not a sign that the pan is wrong or that the glass is cracked. It is a sensor circuit reading.
What you may
notice with it.
The cooktop problems E44 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Element Not Heating
6 causes, cheapest first
Where E44 usually leads
Induction board and coil repair.
Wolf
cooktops.
The cooking half of Sub-Zero Group, selling cooktops and rangetops from its Wisconsin base.
Wolf cooktop repairMore Wolf codes
All 15 Wolf codesTemperature and overheat sensors on other makes
All 51 codes of this kind
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In Wolf's own words
Generator burner sensor open
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Wolf CT series induction cooktops.
Wolf E44 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E44.
Can I clear E44 myself?
Why did one Wolf induction burner stop working with E44?
Is it safe to use my Wolf cooktop with E44 showing?
Which burner does E44 shut down on a Wolf CT induction cooktop?
Back to your everyday
Still showing E44?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.