Dacor induction cooktop
showing C0
On a Dacor Modernist induction cooktop, C0 means the top sensor, which watches the temperature of the glass, is reading open.
Mon–Sat, 8am–8pm
- Temperature and overheat sensors
- Induction board and coil repair
- Source: Dacor
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What C0
actually means.
On a Dacor Modernist induction cooktop, C0 means the top sensor, which watches the temperature of the glass, is reading open. Without that reading the cooktop cannot judge how hot the surface is, so it stops.
Dacor cooktop display
What to do when C0 shows on the cooktopKind of codeTemperature and overheat sensors
A sensor under the glass or on a board reported a reading the control rejected, or heat climbing past the safe limit — often after an empty pan was left on a zone. The zone is allowed to cool and a loose sensor plug is ruled out before the sensor, the coil assembly or the board is blamed. A top that keeps getting hotter is switched off at the breaker first.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Element Not Heating
A coil stays black, a radiant ring under the glass never glows, or a zone warms so weakly that a pot of water will not boil.
MakeDacor
A luxury make, part of Samsung, whose built-in cooktops show up in higher-end US kitchens.
SourceDacor Modernist induction cooktop user manual, Information codes
Dacor Modernist induction cooktops DTI30M977BB and DTI36M977BB (manual dated 2017). Dacor gas cooktops and rangetops do not use this list.
Before you book,
in this order.
Each step comes from Dacor's own guidance for C0 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Turn the cooktop off and on again.
If C0 stays, unplug the cooktop or switch its breaker off for at least 30 seconds, then reconnect.
Book a visit if the code does not clear.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
C0 is not a cookware warning and does not mean the glass is cracked. It is the sensor circuit.
What you may
notice with it.
The cooktop problems C0 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Element Not Heating
6 causes, cheapest first
Where C0 usually leads
Induction board and coil repair.
Dacor
cooktops.
A luxury make, part of Samsung, whose built-in cooktops show up in higher-end US kitchens.
Dacor cooktop repair
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
Rangetop
A pro-style gas cooking top with its knobs across the front, set into a notch above a base cabinet, often with a griddle or char-broiler beside the burners.
In Dacor's own words
The top sensor is open.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Dacor Modernist induction cooktops DTI30M977BB and DTI36M977BB (manual dated 2017). Dacor gas cooktops and rangetops do not use this list.
Dacor C0 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about C0.
Can I clear C0 myself?
What is the top sensor on my Dacor induction cooktop?
Can I keep cooking on my Dacor with C0?
Can a restart clear C0 on a Dacor DTI30M977BB or DTI36M977BB induction cooktop?
Back to your everyday
Still showing C0?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.