Fulgor Milano induction cooktop
showing E9
E9 means the temperature sensor on one of the induction coils is defective.
Mon–Sat, 8am–8pm
- Temperature and overheat sensors
- Induction board and coil repair
- Source: Fulgor Milano
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E9
actually means.
E9 means the temperature sensor on one of the induction coils is defective. The cooktop cannot watch that coil's temperature, and Fulgor's remedy is to exchange the sensor.
Fulgor Milano cooktop display
What to do when E9 shows on the cooktopKind of codeTemperature and overheat sensors
A sensor under the glass or on a board reported a reading the control rejected, or heat climbing past the safe limit — often after an empty pan was left on a zone. The zone is allowed to cool and a loose sensor plug is ruled out before the sensor, the coil assembly or the board is blamed. A top that keeps getting hotter is switched off at the breaker first.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Element Not Heating
A coil stays black, a radiant ring under the glass never glows, or a zone warms so weakly that a pot of water will not boil.
MakeFulgor Milano
An Italian maker of built-in cooking appliances sold through US luxury dealers.
SourceFulgor Milano S700 induction cooktop use and care manual (archived)
Fulgor Milano S700 induction cooktops (F7IT30S1, F7IT36S1); read from the archived use and care manual. The Enova (F7EIK, F7ECIK) and Sofia induction rangetop manuals were not checked for the same table.
Before you book,
in this order.
Each step comes from Fulgor Milano's own guidance for E9 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Stop using the zone that shows E9.
Note which zone shows E9, since each coil carries its own sensor.
Book a visit to have the sensor replaced.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
E9 is not an overheating stop like E2. Cooling the cooktop will not bring the sensor back.
What you may
notice with it.
The cooktop problems E9 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Element Not Heating
6 causes, cheapest first
Where E9 usually leads
Induction board and coil repair.
Fulgor Milano
cooktops.
An Italian maker of built-in cooking appliances sold through US luxury dealers.
Fulgor Milano cooktop repairMore Fulgor Milano codes
All 14 Fulgor Milano codesTemperature and overheat sensors on other makes
All 50 codes of this kind
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In Fulgor Milano's own words
Coil temperature sensor defective
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Fulgor Milano S700 induction cooktops (F7IT30S1, F7IT36S1); read from the archived use and care manual. The Enova (F7EIK, F7ECIK) and Sofia induction rangetop manuals were not checked for the same table.
Fulgor Milano E9 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E9.
Can I clear E9 myself?
Is E9 on a Fulgor Milano cooktop a big repair?
Why does E9 show on one Fulgor Milano zone only?
Why can't the Fulgor Milano S700 simply run a zone with a failed coil sensor?
Back to your everyday
Still showing E9?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.