JennAir cooktop
showing F36
F36 and F37 on a JennAir cooktop point to a temperature sensor on an induction coil.
Mon–Sat, 8am–8pm
- Temperature and overheat sensors
- Induction board and coil repair
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F36
actually means.
F36 and F37 on a JennAir cooktop point to a temperature sensor on an induction coil. Without a good reading, the cooktop limits or stops that zone.
JennAir cooktop display · also shown as F37
What to do when F36 shows on the cooktopKind of codeTemperature and overheat sensors
A sensor under the glass or on a board reported a reading the control rejected, or heat climbing past the safe limit — often after an empty pan was left on a zone. The zone is allowed to cool and a loose sensor plug is ruled out before the sensor, the coil assembly or the board is blamed. A top that keeps getting hotter is switched off at the breaker first.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Element Not Heating
A coil stays black, a radiant ring under the glass never glows, or a zone warms so weakly that a pot of water will not boil.
MakeJennAir
Whirlpool's luxury label and the name long linked with the downdraft cooktop.
SourceJennAir product help: F36, F37, electric and induction cooktop
JennAir electric and induction cooktops (the code concerns induction coils).
Before you book,
in this order.
Each step comes from JennAir's own guidance for F36 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Reset the power at the breaker for one minute.
If F36 or F37 returns, book a visit; a technician needs to test the coil sensor.
Until the visit, use only the zones that still heat, and switch the breaker off if the code keeps returning.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
F36 and F37 are not pan messages. They point to a temperature sensor on an induction coil.
What you may
notice with it.
The cooktop problems F36 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Where F36 usually leads
Induction board and coil repair.
JennAir
cooktops.
Whirlpool's luxury label and the name long linked with the downdraft cooktop.
JennAir cooktop repairMore JennAir codes
All 15 JennAir codesTemperature and overheat sensors on other makes
All 51 codes of this kind
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In JennAir's own words
There may be a problem with a temperature sensor on an induction coil.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. JennAir electric and induction cooktops (the code concerns induction coils).
JennAir F36 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F36.
Can I clear F36 myself?
Does F37 mean something different from F36 on JennAir?
Can one JennAir zone fail with F36 while the rest work?
Is F36 on a JennAir induction cooktop something I can test at home?
Back to your everyday
Still showing F36?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.