JennAir induction cooktop
showing F0E1
F0E1 on a JennAir induction cooktop comes back to the cookware.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F0E1
actually means.
F0E1 on a JennAir induction cooktop comes back to the cookware. A pan without enough magnetic metal in its base, one too small for the zone or one placed off-center may not be recognized, and the zone will not switch on.
JennAir cooktop display
What to do when F0E1 shows on the cooktopKind of codeMode, not a failure
A state the cooktop was put in, or one it picked deliberately — a child lock, a demo mode that lights the keys but heats nothing, a residual-heat letter over a zone that is still warm, a prompt that no pan has been found. Nothing has broken and no part is called for.
Usually leads toNo repair
Press the On/Off key twice to clear F0E1.
Shows up asInduction Cooktop Not Detecting Pan
An induction zone flashes a pan symbol, beeps, or switches itself off even though a pot is sitting squarely on it.
MakeJennAir
Whirlpool's luxury label and the name long linked with the downdraft cooktop.
SourceJennAir product help: F0E1, induction cooktop
JennAir induction cooktops.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F0E1 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Press the On/Off key twice to clear F0E1.
Check the pan with a magnet and center a flat, magnetic pan of the right size on the zone.
Try a different zone or pan; book a visit if every good pan gives F0E1.
Cleared?
The cooktop came right without a new part. If the same message returns while a zone or burner is on, or the top shuts itself down again mid-meal, treat it as a fresh problem and book it.
What not to do
F0E1 is not a failed coil when the cookware is the cause. Test with a known induction pan first.
What you may
notice with it.
The cooktop problems F0E1 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Induction Cooktop Not Detecting Pan
6 causes, cheapest first
No repair indicated
Nothing to repair.
A state the cooktop was put in, or one it picked deliberately — a child lock, a demo mode that lights the keys but heats nothing, a residual-heat letter over a zone that is still warm, a prompt that no pan has been found. Nothing has broken and no part is called for.
JennAir
cooktops.
Whirlpool's luxury label and the name long linked with the downdraft cooktop.
JennAir cooktop repairMore JennAir codes
All 15 JennAir codesMode, not a failure on other makes
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In JennAir's own words
Press On/Off button twice to remove the F0E1 code and restore the functionality of the cooking zone.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. JennAir induction cooktops.
JennAir F0E1 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F0E1.
Can I clear F0E1 myself?
Why does my JennAir induction cooktop reject my stainless pan?
Can a pan that worked before cause F0E1?
How do I clear F0E1 from a JennAir induction cooking zone?
Back to your everyday
Still showing F0E1?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.