JennAir cooktop
showing F8
F8 on a JennAir electric or induction cooktop means the surface cooking area has been on too long and its automatic shutoff activated.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: JennAir
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F8
actually means.
F8 on a JennAir electric or induction cooktop means the surface cooking area has been on too long and its automatic shutoff activated. It is a safety feature doing its job.
JennAir cooktop display
What to do when F8 shows on the cooktopKind of codeMode, not a failure
A state the cooktop was put in, or one it picked deliberately — a child lock, a demo mode that lights the keys but heats nothing, a residual-heat letter over a zone that is still warm, a prompt that no pan has been found. Nothing has broken and no part is called for.
Usually leads toNo repair
Turn the cooking area off and remove the pan.
Shows up asCooktop Element Not Heating
A coil stays black, a radiant ring under the glass never glows, or a zone warms so weakly that a pot of water will not boil.
MakeJennAir
Whirlpool's luxury label and the name long linked with the downdraft cooktop.
SourceJennAir product help: F8, electric and induction cooktop
JennAir electric and induction cooktops.
Before you book,
in this order.
Each step comes from JennAir's own guidance for F8 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Turn the cooking area off and remove the pan.
Let the area cool, then start again if you still need it.
Book a visit only if F8 appears shortly after a zone is started.
Cleared?
The cooktop came right without a new part. If the same message returns while a zone or burner is on, or the top shuts itself down again mid-meal, treat it as a fresh problem and book it.
What not to do
F8 does not indicate a failed part. It means the automatic shutoff stopped a surface cooking area that ran too long.
What you may
notice with it.
The cooktop problems F8 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Element Not Heating
6 causes, cheapest first
No repair indicated
Nothing to repair.
A state the cooktop was put in, or one it picked deliberately — a child lock, a demo mode that lights the keys but heats nothing, a residual-heat letter over a zone that is still warm, a prompt that no pan has been found. Nothing has broken and no part is called for.
JennAir
cooktops.
Whirlpool's luxury label and the name long linked with the downdraft cooktop.
JennAir cooktop repairMore JennAir codes
All 15 JennAir codesMode, not a failure on other makes
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In JennAir's own words
The surface cooking area automatic shutoff was activated.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. JennAir electric and induction cooktops.
JennAir F8 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F8.
Can I clear F8 myself?
Why did my JennAir cooktop shut off during a long simmer?
Should I worry about F8 on my JennAir?
Can I restart a JennAir surface cooking area right after F8?
Back to your everyday
Still showing F8?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.