Miele induction cooktop
showing F
A lone F on a Miele cooktop means one or more sensor controls stayed covered for roughly ten seconds, by a finger, a boil-over or an object.
Mon–Sat, 8am–8pm
- Touch controls and keys
- Touch control repair
- Source: Miele
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F
actually means.
A lone F on a Miele cooktop means one or more sensor controls stayed covered for roughly ten seconds, by a finger, a boil-over or an object. Miele also points to nearly invisible limescale from dried drops as a cause when the controls look clean.
Miele cooktop display
What to do when F shows on the cooktopKind of codeTouch controls and keys
A key on the glass was held down too long, pressed with nothing there, or stopped answering altogether. Water, a spill or a pan resting on the key strip is ruled out first, then the touch board and its ribbon cable. If a zone keeps heating while the keys are dead, switch the cooktop off at the breaker.
Usually leads toTouch control repair
Glass touch keys and sliders that ignore a finger, start zones by themselves or stay locked, traced to the keys, the control board or the lock setting.
Shows up asCooktop Controls Unresponsive
Touch keys or a slider do nothing, the display lights but ignores every press, or a knob turns without starting its burner or element.
MakeMiele
A family-owned German maker known for built-in appliances, including cooktops.
SourceMiele USA cooktop support: F on the display
Miele gives this for its induction cooktops; a separate Miele page covers F on a panel that looks clean.
Before you book,
in this order.
Each step comes from Miele's own guidance for F on its cooktops. Follow it to the end: the last card says whether this is a visit.
Clean and dry the control area, then switch the cooktop on again with the On/Off control.
Take pans, utensils and towels off the sensor controls before switching the cooktop back on.
If F keeps coming back on a clean, dry panel, book a visit.
What not to do
F by itself is not an F-number code such as F31. It is about the controls being covered.
What you may
notice with it.
The cooktop problems F tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Controls Unresponsive
5 causes, cheapest first
Where F usually leads
Touch control repair.
Miele
cooktops.
A family-owned German maker known for built-in appliances, including cooktops.
Miele cooktop repairMore Miele codes
All 15 Miele codesTouch controls and keys on other makes
All 37 codes of this kind
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In Miele's own words
One or more of the sensor controls remain(s) covered for longer than approx. 10 s
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Miele gives this for its induction cooktops; a separate Miele page covers F on a panel that looks clean.
Miele F cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F.
Can I clear F myself?
My Miele shows F but nothing is on the controls. Why?
Do I need to cut the power after F?
How long does a Miele sensor control have to be covered before F appears?
Back to your everyday
Still showing F?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.