Maytag cooktop
showing HOT
Maytag shows H or HOT in the heat setting window whenever a cooking area is too hot to touch, even after it has been switched off.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: Maytag
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What HOT
actually means.
Maytag shows H or HOT in the heat setting window whenever a cooking area is too hot to touch, even after it has been switched off. It is a burn warning built into the glass cooktop.
Maytag cooktop display · also shown as H
What to do when HOT shows on the cooktopKind of codeMode, not a failure
A state the cooktop was put in, or one it picked deliberately — a child lock, a demo mode that lights the keys but heats nothing, a residual-heat letter over a zone that is still warm, a prompt that no pan has been found. Nothing has broken and no part is called for.
Usually leads toNo repair
Keep hands and hot-sensitive items off the zone until the H goes out.
Shows up asCooktop Hot Surface Light Stays On
The hot surface light or residual heat indicator stays lit long after the glass has cooled, or it never comes on at all.
MakeMaytag
A Whirlpool brand long sold on durability, found on older built-in cooktops in many US homes.
SourceMaytag Product Help: Displaying H or HOT, electric cooktop
Maytag electric cooktops.
Before you book,
in this order.
Each step comes from Maytag's own guidance for HOT on its cooktops. Follow it to the end: the last card says whether this is a visit.
Keep hands and hot-sensitive items off the zone until the H goes out.
If H stays lit or flashes after the glass has cooled, reset the breaker for one minute.
If it still shows on cold glass, book a visit.
Cleared?
The cooktop came right without a new part. If the same message returns while a zone or burner is on, or the top shuts itself down again mid-meal, treat it as a fresh problem and book it.
What not to do
HOT is not an error. It only needs attention when it stays lit on glass that is cold.
What you may
notice with it.
The cooktop problems HOT tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Hot Surface Light Stays On
5 causes, cheapest first
No repair indicated
Nothing to repair.
A state the cooktop was put in, or one it picked deliberately — a child lock, a demo mode that lights the keys but heats nothing, a residual-heat letter over a zone that is still warm, a prompt that no pan has been found. Nothing has broken and no part is called for.
Maytag
cooktops.
A Whirlpool brand long sold on durability, found on older built-in cooktops in many US homes.
Maytag cooktop repairMore Maytag codes
Mode, not a failure on other makes
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In Maytag's own words
An H or HOT will display in the heat setting window when any surface cooking area is too hot to touch
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Maytag electric cooktops.
Maytag HOT cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about HOT.
Can I clear HOT myself?
Why does my Maytag cooktop show HOT after I switched it off?
When is a lit HOT worth a service call?
Where does the HOT warning appear on a Maytag cooktop?
Back to your everyday
Still showing HOT?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.