Thermador induction cooktop
showing E9000
E9000 and E9010 carry the same meaning as U400 on Thermador's list: the supply voltage is outside the normal range.
Mon–Sat, 8am–8pm
- Induction power and coils
- Induction board and coil repair
- Source: Thermador
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E9000
actually means.
E9000 and E9010 carry the same meaning as U400 on Thermador's list: the supply voltage is outside the normal range.
Thermador cooktop display · also shown as E9010
What to do when E9000 shows on the cooktopKind of codeInduction power and coils
An induction zone could not drive its coil as the board planned: no pan was detected, the current ran too high or too low, or the power stage reported trouble. The pan base, the supply voltage and a clogged air intake are checked before the coil or the power board is replaced, and a top that trips its breaker is left switched off until then.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Tripping Breaker
The circuit breaker for the cooktop trips as a burner or zone switches on, at one particular setting, or a few minutes into cooking.
MakeThermador
A BSH-owned luxury brand that lists gas, electric and induction cooktops alongside pro-style rangetops.
SourceThermador induction cooktop error codes (US support)
Listed on Thermador's induction cooktop page.
Before you book,
in this order.
Each step comes from Thermador's own guidance for E9000 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Switch the cooktop off at the breaker.
Call your electrical utility provider first, as Thermador's list suggests.
Have the supply measured, then book a visit if the circuit checks out.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
These codes do not describe a zone or a pan problem. They describe the voltage arriving at the cooktop.
What you may
notice with it.
The cooktop problems E9000 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Tripping Breaker
6 causes, cheapest first
Where E9000 usually leads
Induction board and coil repair.
Thermador
cooktops.
A BSH-owned luxury brand that lists gas, electric and induction cooktops alongside pro-style rangetops.
Thermador cooktop repairMore Thermador codes
All 14 Thermador codesInduction power and coils on other makes
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
Rangetop
A pro-style gas cooking top with its knobs across the front, set into a notch above a base cabinet, often with a griddle or char-broiler beside the burners.
In Thermador's own words
E9000 or E9010
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Listed on Thermador's induction cooktop page.
Thermador E9000 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E9000.
Can I clear E9000 myself?
Are E9000 and E9010 the same on a Thermador?
Could a new circuit cause E9000?
Who does Thermador send me to first for E9000?
Back to your everyday
Still showing E9000?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.