Frigidaire Professional induction cooktop
showing C0
C marks a problem condition.
Mon–Sat, 8am–8pm
- Boards and communication
- Touch control repair
- Source: Frigidaire
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What C0
actually means.
C marks a problem condition. On these cooktops an error in any zone is reported as C0 in zone 1 or 2 on the left, and it replaces HE if that zone is hot.
Frigidaire cooktop display · also shown as C
What to do when C0 shows on the cooktopKind of codeBoards and communication
The touch board and the power board under the glass lost track of each other, or one failed its own start-up check. A power dip, a ribbon or harness pulled loose when the top was fitted, or moisture from a boil-over is ruled out before a board is replaced, and a cooktop that keeps heating while this code shows is switched off at the breaker.
Usually leads toTouch control repair
Glass touch keys and sliders that ignore a finger, start zones by themselves or stay locked, traced to the keys, the control board or the lock setting.
Shows up asCooktop Controls Unresponsive
Touch keys or a slider do nothing, the display lights but ignores every press, or a knob turns without starting its burner or element.
MakeFrigidaire
One of the most common US kitchen makes, found in many homes and rentals with a built-in cooktop.
SourceFrigidaire Professional induction cooktop (PCCI3080AF) user manual
Knob-controlled Frigidaire Professional induction cooktops (the manual linked from the PCCI3080AF page); each knob has its own small display.
Before you book,
in this order.
Each step comes from Frigidaire's own guidance for C0 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Turn the knobs to OFF to reset the surface controls.
Leave the cooktop breaker off if C0 comes back after the knob reset, instead of cooking on the other zones.
If C or C0 remains and the knobs do not work, book a visit.
What not to do
C0 is not the hot element message; it takes priority over HE. Its position on the left knobs does not mean the problem is in zone 1 or 2.
What you may
notice with it.
The cooktop problems C0 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Where C0 usually leads
Touch control repair.
Frigidaire
cooktops.
One of the most common US kitchen makes, found in many homes and rentals with a built-in cooktop.
Frigidaire cooktop repairMore Frigidaire codes
Boards and communication on other makes
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Electric cooktop
A coil or smooth-glass radiant cooking surface built into the countertop and wired to its own circuit in the cabinet or wall behind it.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
In Frigidaire's own words
In case of an error in any of the zones, the C0 appears in zones 1 or 2
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Knob-controlled Frigidaire Professional induction cooktops (the manual linked from the PCCI3080AF page); each knob has its own small display.
Frigidaire C0 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about C0.
Can I clear C0 myself?
Why does C0 appear on the left knob even if I used a right zone?
Is C0 something I can fix at home?
What does a plain C mean on a Frigidaire Professional knob display?
Back to your everyday
Still showing C0?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.