ZLINE RCIND induction cooktop
showing E2/E3
The RCIND manual lists E2 and E3 together: the voltage supplied to the cooktop is too low.
Mon–Sat, 8am–8pm
- Induction power and coils
- Induction board and coil repair
- Source: ZLINE
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What E2/E3
actually means.
The RCIND manual lists E2 and E3 together: the voltage supplied to the cooktop is too low. ZLINE's step is to check that the power supply is normal and to power on again once it is.
ZLINE cooktop display · also shown as E2, E3
What to do when E2/E3 shows on the cooktopKind of codeInduction power and coils
An induction zone could not drive its coil as the board planned: no pan was detected, the current ran too high or too low, or the power stage reported trouble. The pan base, the supply voltage and a clogged air intake are checked before the coil or the power board is replaced, and a top that trips its breaker is left switched off until then.
Usually leads toInduction board and coil repair
Induction zones that stop sensing pans, cut out, buzz or show codes, traced to the power boards, the coils, their sensors and the links to the controls.
Shows up asCooktop Element Not Heating
A coil stays black, a radiant ring under the glass never glows, or a zone warms so weakly that a pot of water will not boil.
MakeZLINE
A US company that sells gas cooktops and rangetops, often bought online and installed by the owner's own contractor.
SourceZLINE RCIND induction cooktop user manual
ZLINE RCIND induction cooktops (RCIND-24, RCIND-30, RCIND-36), June 2024 user manual. The manual pairs its codes, and the same numbers mean other things on the newer FCIND.
Before you book,
in this order.
Each step comes from ZLINE's own guidance for E2/E3 on its cooktops. Follow it to the end: the last card says whether this is a visit.
Check the breaker and whether other appliances on the same supply are struggling.
Leave the supply wiring and junction box to an electrician, and keep the breaker off while any of it is checked.
Power the cooktop on again after the supply is normal; if the code persists, book a visit.
Still there?
It usually turns into induction board and coil repair. Book with the code and the model number.
What not to do
On the newer FCIND, E2 is an overheating code and E3 is high voltage. The RCIND list is different.
What you may
notice with it.
The cooktop problems E2/E3 tends to arrive with. Answer these at the cooktop before anyone is booked.
All problems
Cooktop Element Not Heating
6 causes, cheapest first
Where E2/E3 usually leads
Induction board and coil repair.
ZLINE
cooktops.
A US company that sells gas cooktops and rangetops, often bought online and installed by the owner's own contractor.
ZLINE cooktop repairMore ZLINE codes
All 16 ZLINE codesInduction power and coils on other makes
Gas cooktop
A gas cooking surface dropped into a countertop cutout, with its gas line and power cord running down into the cabinet underneath.
Induction cooktop
A glass cooktop in the counter that heats the pan itself through magnetic coils, run by power boards and cooled by a fan underneath.
Rangetop
A pro-style gas cooking top with its knobs across the front, set into a notch above a base cabinet, often with a griddle or char-broiler beside the burners.
In ZLINE's own words
Supplied voltage to
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. ZLINE RCIND induction cooktops (RCIND-24, RCIND-30, RCIND-36), June 2024 user manual. The manual pairs its codes, and the same numbers mean other things on the newer FCIND.
ZLINE E2/E3 cooktop repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about E2/E3.
Can I clear E2/E3 myself?
Why does my ZLINE RCIND show E2 when my FCIND manual calls it overheating?
Who should check a low-voltage code on a ZLINE RCIND?
Why does ZLINE list E2 and E3 together on the RCIND-30?
Back to your everyday
Still showing E2/E3?
Book with the code copied exactly, the full model number, and whether there is any smell of gas or burning — with a code in hand, that is where the diagnosis starts.