Cooktop
Infinite Switch and Knob Repair
Knob-controlled cooktop zones that heat only on high, will not simmer or will not switch off, and the worn knobs and switches behind them.
Mon–Sat, 8am–8pm
- Low cost band
- 5 steps on the visit
- 5 problems it answers
Book a visit
Three short steps, about a minute.
or call (844) 252-4077
Loading appointment form…
The appointment form couldn’t load. Please try again.
What the cooktop infinite switch and knob repair
involves.
Cooktop infinite switch repair is about the part that turns a knob position into a level of heat. An infinite switch holds a small bimetal strip that clicks the element on and off in a timed cycle; the lower the setting, the shorter the on time. After years of cycling the contacts pit or weld, and the zone then heats only at full power, stays cold until high, or keeps heating after the knob reaches off. The same repair covers knobs that slip on a worn shaft, cracked knob inserts and the indicator light wiring that shares the switch. On gas cooktops and rangetops, knobs that no longer grip their valve stems are replaced here too; the valves themselves are a separate job.
How the visit goesWhat it usually costsLow · Infinite switch or knob
A knob is minor, and a switch is a short job reached through the lifted top or the front panel. Burnt terminals on the switch are renewed during the same visit.
Answers 5 problemsCooktop Element Only Heats on High
Cooktop Simmer Too Hot · Cooktop Burner or Element Won't Turn Off · Cooktop Element Not Heating · Cooktop Hot Surface Light Stays On
Comes up most onElectric cooktop
Gas cooktop · Rangetop
Infinite switch and knob repair,
step by step.
Run each zone from low to high and confirm it cycles at low, holds on high and stops at off.
Turn each knob through its travel and note where the zone heats, cycles or stays cold.
Switch off the breaker and open the top or the front panel to reach the switches.
Measure the switch at several settings and look for burnt terminals and heat-marked wire.
Replace the switch and any damaged terminals, and fit new knobs where the old ones slip.
Run each zone from low to high and confirm it cycles at low, holds on high and stops at off.
The problems
it answers.
5 of them, from cooktop element only heats on high to cooktop hot surface light stays on.
All problems
Cooktop Element Only Heats on High
5 causes, cheapest first
Before you call
Tell us this when you book
- Which knob and zone, and at which settings it misbehaves
- Whether the zone stays on after the knob is turned off
- Whether the knob turns freely or slips on its shaft
- Whether the hot-surface light or an indicator acts oddly too
It also answers
Low,
on the site's scale.
A knob is minor, and a switch is a short job reached through the lifted top or the front panel. Burnt terminals on the switch are renewed during the same visit.
Read the full cost guideWhere it
comes up most.
Most bookings: Electric cooktop, Gas cooktop, Rangetop.
All cooktop typesOften the same visit
The makes
we see it on.
29 makes on this site, and the cooktop infinite switch and knob repair on any of them. Each mark opens that make's own page.
All 29 brandsInfinite switch and knob repair,
where we come out.
The kitchen, the climate and the building all change how the cooktop infinite switch and knob repair goes. These notes are about that, metro by metro.
All service areasTampa BayFL · 31 areas
Coil and radiant cooktops in Tampa Bay use an infinite switch behind each knob, and one that sticks on high or cycles unevenly is swapped out from beneath the knob panel once the breaker is off.
OrlandoFL · 30 areas
Orlando rental cooktops take hard use at their knobs, and a cracked knob or a stripped stem is what most often leaves a burner or zone impossible to set, a quick repair done with parts matched to the model.
Miami / South FloridaFL · 47 areas
In South Florida houses with gas cooktops, knobs cleaned with harsh sprays crack and let the liquid seep into the switches below, so a knob replacement often comes with a new spark switch.
New York MetroNY · 75 areas
In New York galley kitchens the front knobs on a gas cooktop get bumped and pulled constantly, and a loose or broken knob that no longer turns the valve its full travel is replaced so the flame can be set properly.
HoustonTX · 36 areas
Houston electric cooktops that heat only at full power, or not at all, often have a burned infinite switch, tested at its terminals and replaced with the breaker off.
ChicagoIL · 50 areas
Chicagoland cooktops that simmer too hot during long winter braises usually have an infinite switch that no longer cycles as it should, and a new switch fitted from under the top restores low heat.
Los AngelesCA · 95 areas
Los Angeles rangetops with heavy metal knobs have shafts and bezels that wear with daily use, and the repair replaces worn knob parts in the maker's finish so the top still matches the kitchen.
San DiegoCA · 31 areas
In San Diego coastal kitchens, knob shafts and infinite switch terminals corrode, so a switch that cuts in and out is replaced and its harness terminals cleaned at the same time.
San Francisco Bay AreaCA · 74 areas
Bay Area gas cooktops in older houses may have knobs and valves decades old, and a knob that spins without moving the valve is repaired with a new knob or stem adapter matched to the model.
Questions about
the cooktop infinite switch and knob repair.
My element clicks on and off at medium. Is the switch failing?
The knob spins but nothing happens. Is it the knob or the switch?
Can one bad switch damage the rest of the cooktop?
Can I change my cooktop knobs to a different style?
Back to your everyday
Ready to book the cooktop infinite switch and knob repair?
Have these to hand: which knob and zone, and at which settings it misbehaves, whether the zone stays on after the knob is turned off, whether the knob turns freely or slips on its shaft, whether the hot-surface light or an indicator acts oddly too.